If you are planning to study Plant Breeding and Seed Technology at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Plant Breeding and Seed Tech.?
No, Redeemer's University, Nigeria does not offer Plant Breeding and Seed Tech. under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Plant Breeding and Seed Tech. course under the Faculty of Agriculture has been updated.
Admission Requirements for Plant Breeding and Seed Technology When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, candidates seeking admission into the Plant Breeding and Seed Technology department under Faculty of Agriculture, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Biology / Agriculture and
RUN Cut-Off Mark for Plant Breeding and Seed Technology
The general UTME cut-off mark is 180, but due to the variation of Plant Breeding and Seed Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
1. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
2. Industrial Chemistry
To study this course, candidates seeking admission into the Industrial Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science.
3. Applied Biology and Genetics
To study this course, candidates seeking admission into the Applied Biology and Genetics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
4. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
5. Civil Engineering
To study this course, candidates aspiring to gain admission into Civil Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
7. Computer Science (CS)
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Nigerian Tertiary Institutions Offering Plant Breeding and Seed Tech. Course