If you are planning to study Shipping and Maritime Technology at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. RUN was established in 2005 by the Redeemed Christian Church of God (RCCG) to provide university education rooted in academic excellence, innovation, and strong moral values. Since its inception, the university has developed into one of Nigeria’s leading private institutions of higher learning. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Shipping and Maritime Technology?
No, Redeemer's University, Nigeria does not offer Shipping and Maritime Technology under its Faculty of Maritime Studies. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Shipping and Maritime Technology course under the Faculty of Maritime Studies has been updated.
Admission Requirements for Shipping and Maritime Technology When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Shipping and Maritime Technology department under Faculty of Maritime Studies, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one (1) other subject (not more than two (2) sittings) from:
RUN Cut-Off Mark for Shipping and Maritime Technology
The general UTME cut-off mark is 180, but due to the variation of Shipping and Maritime Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
1. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
2. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
3. Mechanical Engineering
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
4. Applied Biology and Genetics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Applied Biology and Genetics department.
5. Urban and Regional Planning (URP)
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
6. Human Anatomy
To study this course, the minimum requirement for applicants seeking admission to the Human Anatomy department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
7. Computer Science (CS)
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Nigerian Tertiary Institutions Offering Shipping and Maritime Technology Course