If you are planning to study Mechanical Metalwork Technology Education at Rivers State University formally known as Rivers State University of Science and Technology (RSUST) located in Rivers State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into RSU.
Does Rivers State University (RSU) offer Mechanical Metalwork Technology Education?
No, Rivers State University does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Rivers State University (RSU) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Rivers State University (RSU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
RSU Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RSU Science Courses with their Requirements
Fisheries Management
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Fisheries Management department.
Biology/Agricultural Science,
any other relevant Science subject.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Land Surveying
SSCE Requirements
To study this course, candidates aspiring to gain admission into Land Surveying department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing.
Crop Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Crop Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics is required.
Education and Biology
SSCE Requirements
To study this course, candidates seeking admission into the Education and Biology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biological Science
SSCE Requirements
To study this course, candidates seeking admission into the Biological Science department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any other relevant Science subject.
Agricultural Extension and Rural Development
SSCE Requirements
To study this course, candidates seeking admission into the Agricultural Extension and Rural Development department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Chemistry, Biology / Agricultural Science
Geography, Physics and Economics.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course