If you are planning to study Communication Technology at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. TECH-U was established in 2012 by the Oyo State Government as a specialized institution for science and technology education. It was created to promote innovation, research, and technological advancement in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Communication Technology?
No, The Technical University, Ibadan does not offer Communication Technology under its Faculty of Communication and Media Studies. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Communication Technology course under the Faculty of Communication and Media Studies has been updated.
Admission Requirements for Communication Technology When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Communication Technology department under Faculty of Communication and Media Studies.
any two (2) other relevant subjects.
JAMB Subject Combination
any one of Account, Commerce and Government.
TECH-U Cut-Off Mark for Communication Technology
The general UTME cut-off mark is 180, but due to the variation of Communication Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
1. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
2. Physics With Electronics
To study this course, candidates aspiring to gain admission into Physics With Electronics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject from Further Mathematics and Biology / Agricultural Science.
3. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Urban and Regional Planning (URP)
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
5. Industrial Chemistry
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Chemistry department.
Biology / Agricultural Science.
6. Mechatronics Engineering
To study this course, candidates aspiring to gain admission into Mechatronics Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
7. Biomedical Engineering
To study this course, the minimum requirement for applicants seeking admission to the Biomedical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Nigerian Tertiary Institutions Offering Communication Technology Course