If you are planning to study Geology and Mining at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Geology and Mining?
No, The Technical University, Ibadan does not offer Geology and Mining under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Geology and Mining course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Geology and Mining When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Geology and Mining department under Faculty of Earth and Mineral Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one other relevant subject.
JAMB Subject Combination
Use of English and any three (3) of
TECH-U Cut-Off Mark for Geology and Mining
The general UTME cut-off mark is 180, but due to the variation of Geology and Mining cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Mathematics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Forensic Science
SSCE Requirements
To study this course, candidates aspiring to gain admission into Forensic Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Biotechnology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biotechnology department.
Nigerian Tertiary Institutions Offering Geology and Mining Course