If you are planning to study Geology and Petroleum Studies at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Geology and Petroleum Studies?
No, The Technical University, Ibadan does not offer Geology and Petroleum Studies under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Geology and Petroleum Studies course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Geology and Petroleum Studies When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Geology and Petroleum Studies department under Faculty of Earth and Mineral Sciences, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
JAMB Subject Combination
Any three (3) other subjects from:
TECH-U Cut-Off Mark for Geology and Petroleum Studies
The general UTME cut-off mark is 180, but due to the variation of Geology and Petroleum Studies cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Food Science and Technology (FT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Industrial Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
Chemical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Chemical Engineering department.
any other Science subject.
Biomedical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Biomedical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Geology and Petroleum Studies Course