If you are planning to study Metalwork Technology Education at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Metalwork Technology Education?
No, The Technical University, Ibadan does not offer Metalwork Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Metalwork Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Metalwork Technology Education When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Metalwork Technology Education department under Faculty of Education.
Biology / Agricultural Science, Physics, or Chemistry
and two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
TECH-U Cut-Off Mark for Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Mechatronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Biomedical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biomedical Engineering department.
Microbiology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biotechnology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Biotechnology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Software Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Software Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
Nigerian Tertiary Institutions Offering Metalwork Technology Education Course