If you are planning to study Physics and Computer Electronic at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. TECH-U was established in 2012 by the Oyo State Government as a specialized institution for science and technology education. It was created to promote innovation, research, and technological advancement in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Physics and Computer Electronic?
No, The Technical University, Ibadan does not offer Physics and Computer Electronic under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Physics and Computer Electronic course under the Faculty of Science has been updated.
Admission Requirements for Physics and Computer Electronic When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, candidates seeking admission into the Physics and Computer Electronic department under Faculty of Science, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject from:
Biology or Agricultural Science.
TECH-U Cut-Off Mark for Physics and Computer Electronic
The general UTME cut-off mark is 180, but due to the variation of Physics and Computer Electronic cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
1. Statistics
To study this course, candidates seeking admission into the Statistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
2. Surveying and Geoinformatics
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
3. Forensic Science
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Forensic Science department.
4. Computer Science (CS)
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
5. Building Technology (BT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
6. Petroleum Engineering
To study this course, candidates aspiring to gain admission into Petroleum Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
7. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Physics and Computer Electronic Course