If you are planning to study Prosthesis and Orthopaedic Technology at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. TECH-U was established in 2012 by the Oyo State Government as a specialized institution for science and technology education. It was created to promote innovation, research, and technological advancement in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Prosthesis and Orthopaedic Technology?
No, The Technical University, Ibadan does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology.
TECH-U Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
1. Mechatronics Engineering
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
2. Petroleum Engineering
To study this course, the minimum requirement for applicants seeking admission to the Petroleum Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
3. Food Science and Technology (FT)
To study this course, candidates aspiring to gain admission into Food Science and Technology (FT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
4. Forensic Science
To study this course, candidates aspiring to gain admission into Forensic Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Industrial and Production Engineering
To study this course, candidates aspiring to gain admission into Industrial and Production Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
6. Computer Science (CS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
7. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course