If you are planning to study Physics and Applied Physics at University of Benin located in Edo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. UNIBEN was established in 1970 by the Midwest Regional Government (now Edo State). It is one of Nigeria’s first-generation universities, created to promote higher education, research, and national development. This page explains everything you need to know to increase your chances of gaining admission into UNIBEN.
Does University of Benin (UNIBEN) offer Physics and Applied Physics?
No, University of Benin does not offer Physics and Applied Physics under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at University of Benin (UNIBEN) below to check if the Physics and Applied Physics course under the Faculty of Science has been updated.
Admission Requirements for Physics and Applied Physics When Accredited in University of Benin (UNIBEN)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics and Applied Physics department under Faculty of Science.
any other Science subject from Further Mathematics and Biology or Agricultural Science.
UNIBEN Cut-Off Mark for Physics and Applied Physics
The general UTME cut-off mark is 180, but due to the variation of Physics and Applied Physics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIBEN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIBEN Science Courses with their Requirements
1. Marine Engineering
To study this course, candidates seeking admission into the Marine Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Mechatronics Engineering
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
3. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Environmental Education
To study this course, candidates seeking admission into the Environmental Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any three (3) relevant subjects from:
Biology, Chemistry, Physics,
Health Science and Agricultural Science.
5. Electrical / Electronics Engineering
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
6. Industrial Physics
To study this course, candidates aspiring to gain admission into Industrial Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject from Further Mathematics and Biology or Agricultural Science.
7. Quantity Surveying (QS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Quantity Surveying (QS) department.
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Tertiary Institutions Offering Physics and Applied Physics Course