If you are planning to study Physical Education at University of Delta, Agbor located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. UNIDEL was established in 2021 by the Delta State Government through the upgrade of Delta State Polytechnic, Ozoro and other institutions into a full university to expand access to higher education. This page explains everything you need to know to increase your chances of gaining admission into UNIDEL.
Does University of Delta (UNIDEL), Agbor offer Physical Education?
No, University of Delta, Agbor does not offer Physical Education under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at University of Delta (UNIDEL), Agbor below to check if the Physical Education course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Physical Education When Accredited in University of Delta (UNIDEL), Agbor
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physical Education department under Faculty of Health and Medical Sciences.
Biology or its Equivalent,
any two (2) relevant subjects.
JAMB Subject Combination
any two (2) relevant subjects.
UNIDEL Cut-Off Mark for Physical Education
The general UTME cut-off mark is 180, but due to the variation of Physical Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIDEL Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIDEL Science Courses with their Requirements
1. Education and Computer Science
To study this course, candidates aspiring to gain admission into Education and Computer Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
three (3) other relevant Science subjects.
2. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
3. Chemistry
To study this course, candidates seeking admission into the Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
4. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Computer Science (CS)
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
6. Environmental Management and Toxicology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Environmental Management and Toxicology department.
7. Mechatronics Engineering
To study this course, candidates seeking admission into the Mechatronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Nigerian Universities Offering Physical Education Course