If you are planning to study Industrial Production Engineering at University of Jos located in Plateau State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. UNIJOS was established in 1971 by the Federal Government of Nigeria to provide higher education opportunities in the North-Central region and support national development through research and teaching. This page explains everything you need to know to increase your chances of gaining admission into UNIJOS.
Does University of Jos (UNIJOS) offer Industrial Production Engineering?
No, University of Jos does not offer Industrial Production Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at University of Jos (UNIJOS) below to check if the Industrial Production Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Production Engineering When Accredited in University of Jos (UNIJOS)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Production Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
UNIJOS Cut-Off Mark for Industrial Production Engineering
The general UTME cut-off mark is 180, but due to the variation of Industrial Production Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIJOS Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIJOS Science Courses with their Requirements
1. Urban and Regional Planning (URP)
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
2. Building
To study this course, candidates aspiring to gain admission into Building department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
3. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
4. Animal Production
To study this course, the minimum requirement for applicants seeking admission to the Animal Production department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
5. Chemistry
To study this course, the minimum requirement for applicants seeking admission to the Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
6. Zoology
To study this course, the minimum requirement for applicants seeking admission to the Zoology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subject.
7. Science Laboratory Technology (SLT)
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Nigerian Tertiary Institutions Offering Industrial Production Engineering Course