If you are planning to study Industrial Technical Education at University of Lagos located in Lagos State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. UNILAG was established in 1962 by the Federal Government of Nigeria as one of the first-generation universities. It was created to promote higher education, research, and national integration. This page explains everything you need to know to increase your chances of gaining admission into UNILAG.
Does University of Lagos (UNILAG) offer Industrial Technical Education?
No, University of Lagos does not offer Industrial Technical Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at University of Lagos (UNILAG) below to check if the Industrial Technical Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Technical Education When Accredited in University of Lagos (UNILAG)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Technical Education department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Mathematics / Physics and
any other three (3) relevant subjects.
UNILAG Cut-Off Mark for Industrial Technical Education
The general UTME cut-off mark is 180, but due to the variation of Industrial Technical Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNILAG Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNILAG Science Courses with their Requirements
1. Mechanical Engineering
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
2. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
3. Education and Mathematics
To study this course, candidates seeking admission into the Education and Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) other Science subject, and
any other relevant subjects.
4. Physics
To study this course, candidates seeking admission into the Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
5. Nursing (Science)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Nursing (Science) department.
6. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Health Education
To study this course, candidates aspiring to gain admission into Health Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Industrial Technical Education Course