If you are planning to study Physical and Health Education at University of Nigeria, Nsukka located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into UNN.
Does University of Nigeria, Nsukka (UNN) offer Physical and Health Education?
No, University of Nigeria, Nsukka does not offer Physical and Health Education under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at University of Nigeria, Nsukka (UNN) below to check if the Physical and Health Education course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Physical and Health Education When Accredited in University of Nigeria, Nsukka (UNN)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Physical and Health Education department under Faculty of Health and Medical Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology or its equivalent
and any two (2) other relevant subjects.
JAMB Subject Combination
any two (2) relevant subjects.
UNN Cut-Off Mark for Physical and Health Education
The general UTME cut-off mark is 180, but due to the variation of Physical and Health Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNN Science Courses with their Requirements
Veterinary Medicine
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Veterinary Medicine department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Physics / Astrology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics / Astrology department.
any other Science subject from:
Biology or Agricultural Science.
Medicine and Surgery
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medicine and Surgery department.
Education and Chemistry
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Chemistry department.
Biology and Agricultural Science.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Metallurgical and Material Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Metallurgical and Material Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
Nigerian Universities Offering Physical and Health Education Course