If you are planning to study Production Engineering at University of Nigeria, Nsukka located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. UNN was established in 1960 as a federal university located in Nsukka, Enugu State. It was founded as the first full-fledged indigenous university in Nigeria, aimed at promoting higher education, research, and national development. This page explains everything you need to know to increase your chances of gaining admission into UNN.
Does University of Nigeria, Nsukka (UNN) offer Production Engineering?
No, University of Nigeria, Nsukka does not offer Production Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at University of Nigeria, Nsukka (UNN) below to check if the Production Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Production Engineering When Accredited in University of Nigeria, Nsukka (UNN)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Production Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
UNN Cut-Off Mark for Production Engineering
The general UTME cut-off mark is 180, but due to the variation of Production Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNN Science Courses with their Requirements
1. Home Science
To study this course, candidates seeking admission into the Home Science department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
Chemistry, Mathematics and
at least ‘O’ Level pass in English Language and Physics.
General Metal Work, General Wood Work, Building / Engineering Drawing, Furniture Design and Construction, Upholstery Design and Construction,
Spray Painting and Period Furniture, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing and Basic Electricity.
2. Dentistry and Dental Surgery
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Dentistry and Dental Surgery department.
3. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Education and Mathematics
To study this course, candidates aspiring to gain admission into Education and Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one (1) other Science subject, and
any other relevant subjects.
5. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Computer with Statistics
To study this course, candidates aspiring to gain admission into Computer with Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology, Chemistry, Physics,
Further Maths, and Technical Drawing.
7. Mathematics
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Production Engineering Course