If you are planning to study Wildlife Management at University of Nigeria, Nsukka located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. UNN was established in 1960 as a federal university located in Nsukka, Enugu State. It was founded as the first full-fledged indigenous university in Nigeria, aimed at promoting higher education, research, and national development. This page explains everything you need to know to increase your chances of gaining admission into UNN.
Does University of Nigeria, Nsukka (UNN) offer Wildlife Management?
No, University of Nigeria, Nsukka does not offer Wildlife Management under its Faculty of Renewable and Natural Resources. However, since our course list is updated regularly, you can visit the courses available at University of Nigeria, Nsukka (UNN) below to check if the Wildlife Management course under the Faculty of Renewable and Natural Resources has been updated.
Admission Requirements for Wildlife Management When Accredited in University of Nigeria, Nsukka (UNN)
O’Level Requirements
To study this course, candidates seeking admission into the Wildlife Management department under Faculty of Renewable and Natural Resources, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
any one (1) of Geography, Physics and Economics.
JAMB Subject Combination
Biology / Agricultural Science.
UNN Cut-Off Mark for Wildlife Management
The general UTME cut-off mark is 180, but due to the variation of Wildlife Management cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNN Science Courses with their Requirements
1. Home Science
To study this course, candidates aspiring to gain admission into Home Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
Chemistry, Mathematics and
at least ‘O’ Level pass in English Language and Physics.
General Metal Work, General Wood Work, Building / Engineering Drawing, Furniture Design and Construction, Upholstery Design and Construction,
Spray Painting and Period Furniture, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing and Basic Electricity.
2. Education and Physics
To study this course, candidates aspiring to gain admission into Education and Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects or NTC / NBC.
3. Biochemistry
To study this course, candidates aspiring to gain admission into Biochemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
4. Food Science and Technology (FT)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
5. Nursing (Science)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Nursing (Science) department.
6. Architecture
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
7. Metallurgical and Material Engineering
To study this course, candidates seeking admission into the Metallurgical and Material Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
Nigerian Tertiary Institutions Offering Wildlife Management Course