Report on the Fabrication of Sieve System

Report on the Fabrication of Sieve System

Project / Seminar Material
Reference ID: PS-3209-TM

DEDICATION

This research material titled “Report on the Fabrication of Sieve System” is dedicated to God for his enabling grace, and to all computer enthusiasts who contributed to make life a pleasant experience during my research documentation.

ACKNOWLEDGEMENT

I extend my sincere gratitude to all those who contributed to the completion of this project. Special thanks to my Supervisor (Name of your Supervisor), the Head of Department (Name of your HOD), the Lecturers in the department of Chemical Engineering, Book Authors and Profound Scholars of existing or related project material on “Report on the Fabrication of Sieve System” for their invaluable guidance, support, and expertise throughout the journey.

I am also grateful to your study area (mention any funding organizations, if applicable) for their financial assistance. This research would not have been possible without the encouragement and assistance of some stakeholders (mention any mentors, teachers, or colleagues). Additionally, I would like to acknowledge the understanding and patience of my family and friends during this endeavor. Your unwavering support has been a constant source of motivation. Thank you all for being part of this meaningful endeavor.

ABSTRACT

The construction of sieves system was carried out in the Engineering workshop, Institute of management and technology, Enugu.

The aim of this project is to fabricate a sieve system, which is capable of separating solid particles of various sizes.

The construction was carried out in order to analyze the sizes of particles.

The component parts of the sets of sieve and their dimension are as follow:

  • Height of sieve —80mm
  • Number of sieve —4
  • Diameter of sieve —230mm
  • Shape of sieve —cirular
  • Height of sieve set —760mm
  • Mesh/hole sizes — top —6.0mm, 2nd 5.0mm, 3rd 3.0mm bottom 1.0mm downwards respectively.

In constructing of this sieve system, some factors were taken into consideration and they are:

  1. The capacity of the sieve
  2. The type of mixture that can be filtered in it
  3. The types of properties and decomposition of the mixture.
  4. The type of material to be used for constructing the sieve.

The cost which is the determinant, factor in fabrication of any equipment.

These factors, help greatly in the fulfillment of the objective of this project study.

At the end of the fabrication, a sieve equipment was construct with specified dimension.

Report on the Fabrication of Sieve System

CHAPTER ONE

1.0 Introduction

Generally, all chemical engineering mostly deals with the construction of sieve among others construction in order to fulfill theory of separations technique. This construction is carried out so as to achieve and put to practice chemical process with the help of some component for equipment construction procedures.

Sieving equipments produces a nice separation of solid particles, although artificially, by allowing the social particles to pass through the pores or the a pasture, which consists of orderly, arrange set of sieves which is arranged in manner with their facilities sizes and shapes.

Sieving equipments operates satisfactory with reasonable coarse and fine particles, so that separation can be done they have high sensitive efficiency, but few have been built since the development of separation of particles, because of the lost and the procedures involved and the labour needed to clean the sieve plate and to handle the sieve equipment.

Moreover, in the construction of set of sieve, we have to bear certain qualities in mind to portray such as determination of size and shape of the equipment which contributes to the efficiency of the equipment.

However, the operation has evolved as a particle at rather than a theoretical science, nevertheless, its theory has received steady attention since the pioneering work of some important scientist half a century ago.

They are usually used in large industries like mining, coal, gold, diamond and pharmaceutical etc, because of its importance and efficiency and would not be seen commonly.

Above all, the purpose of this project is to fabricate a set of sieve which sole aim is for separation of solid particles of different size by passing through the mesh with the help of shaking and larger particles retained on the mesh (oversized) and the particles that passes through (undersized) enables us to separate the particles.

…

CHAPTER TWO

2.0 Literature Review

2.1 Introduction

This chapter focuses on the review of related literature. A literature review includes the current knowledge as well as theoretical and methodological contributions to a particular topic. It documents the state of the art with respect to the topic you are writing. It surveys the literature in the topic selected. In this research work the literature review includes the …

Summary Headlines for Report on the Fabrication of Sieve System