	PARKLYN ERVICES	·	RC: 2994849

Does HUKPOLY Offer Education and Physics | POLY Enquiry

facebook Page

WhatsApp Channel

Is Education and Physics Offered in Hassan Usman Katsina Polytechnic (HUKPOLY)?

If you are planning to study Education and Physics at Hassan Usman Katsina Polytechnic located in Katsina State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into HUKPOLY.

Does Hassan Usman Katsina Polytechnic (HUKPOLY) offer Education and Physics?

No, Hassan Usman Katsina Polytechnic does not offer Education and Physics under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Hassan Usman Katsina Polytechnic (HUKPOLY) below to check if the Education and Physics course under the Faculty of Education has been updated.

Admission Requirements for Education and Physics When Accredited in Hassan Usman Katsina Polytechnic (HUKPOLY)

O’Level Requirements

To study this course, candidates aspiring to gain admission into Education and Physics department under Faculty of Education, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Physics,
Mathematics, and
two (2) other Science subjects or NTC / NBC.

JAMB Subject Combination

Use of English,
Physics,
Mathematics / Chemistry, and
one (1) other subject.

HUKPOLY Cut-Off Mark for Education and Physics

The general UTME cut-off mark is 180, but due to the variation of Education and Physics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from HUKPOLY Officials. However, to improve your admission chances:

Aim for 180+ score.
Perform well in Post-UTME screening.

Other HUKPOLY Science Courses with their Requirements

Statistics

SSCE Requirements

To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Mathematics,
Physics,
Chemistry and
any other relevant subject.

Mechanical Engineering Technology

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering Technology department.

English Language,
Mathematics,
Physics, Chemistry and
any one subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.

Fisheries Technology

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Fisheries Technology department.

Biology / Agricultural Science,
Chemistry,
Mathematics,
English Language and
any other Science subject.

Computer Science (CS)

SSCE Requirements

To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Physics,
Mathematics, and
any two (2) other Science subjects.

Quantity Surveying (QS)

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Quantity Surveying (QS) department.

English Language,
Mathematics,
Physics,
Chemistry and
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.

Welding and Fabrication Technology

SSCE Requirements

To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Welding and Fabrication Technology department.

Mathematics,
Physics,
Chemistry and
any two subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.

Agricultural Engineering / Technology

SSCE Requirements

To study this course, candidates aspiring to gain admission into Agricultural Engineering / Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

Mathematics,
English Language,
Physics and
any three of the following:
Biology / Agricultural Science, Chemistry, Technical Drawing, Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology / Agricultural Science / Food and Nutrition.