1.0 Introduction
1.1 Background of the Study
Emenite Limited Enugu a member of the Beligian Etex Group started operation in 1963 under the name “Turners Asbestos Cement Company Nigeria Limited: The company was incorporated in 1961 with registration number RC 2712.
The group came to Nigeria with the establishment of her first of four companies in Ikeja, Lagos, Nigeria Limited. The other three are Eternite Limited, Sapele, Giwarite Limited, Kano and Emenite Limited, Enugu.
Emenite Limited after being established have to following as shareholders.
- Turners & Newall Ltd — 80%
- Government of Eastern Nigeria — 20%
As a result of the indigenization decree of 1973, the shareholders of the company changed as follows
- Turners & Newall Ltd — 60%
- Government of Eastern Nigeria — 40%
With the name of the company changing to Turners Building Product (Emene) Limited.
Due to dwindling fortunes of the company, in March 24, 1988 Turners and Newall Ltd divested its interest in the company and transferred 51% of its shareholding to Eteroutremer Societe Anonyme of Belgium (now Etex Group S.A) and the balance of 49% went to then Anambra and Imo State; now Anambra, Enugu, Imo, Abia and Ebonyi States. As a result of the new shareholding arrangement, the company changed its name to Emenite Limited as its presently known.
Emenite Limited after being established in 1963 rolled out her first finished sheets in December that year. The company has a total workforce as at its establishment of 67 staff, its second machine was installed in 1979 while the third was installed in 1983. From a workforce of 67 to 225 staff, from one shift machine to three, from 14,000 tonnes of roofing and ceiling sheets to 50,000 tonnes per year. The company has continued to grow tremendously.
The company has made considerable progress in terms of product development in the market. It operates in the roofing and ceiling market, its range of products include: Bigsix & standard ultimate corrugated sheets of different colours (Grey, Red & Green), prestige concrete tile, Emcee flat sheet, duraceile decorative ceiling, Emlux decorative ceiling as well as Qualitile decorative ceiling and a new product called duratile. These products are sold through a wide range of distribution network located in such a place that they will be close to project sites. Emenite is 150 certified, 150 9002 in 1998, 180 9001 in 2002.
It is the company's quality policy to provide high quality building products to the markets. But much recently there have been complaints from building and construction companies over the quality durability of her products. It is in view of this problem this research work is being undertaken.
1.2 Purpose of the Study
Consumers of goods and services rely on quality standard products displayed for consumers. What is responsible for this trend? Is statistical quality control standard still made use of in industries? This are what this research project intend to solve and make appropriate recommendation.
The project research will
- Determine the process standards and establish the process capability
- Check if the process average and variability are under control in respect of the measurement of flat sheet.
- Check if the process average and variability are under control in respect of the measurement of corrugated sheets
- Set up appropriate control charts for monitoring the future output of the process.
1.3 Significance of the Study
The significance of this research work is to provide information for the management to fine — tune its quality policy concerning their products as obtained in this analysis of this research work. This will be of benefits t o the producers and consumers as well.
1.4 Statement of Research Problem
There have been complaints and doubts that most asbestos roofing sheets in recent times full short of required standard, also whether established standardize are still maintained. This was as a result of reported cases of easy damage and non-durable nature of these sheets.
In view of this, the researcher intends to carry out this research using Emenite Limited Enugu as a case study.
1.5 Research Hypothesis
- H0: The process is not under control in respect of the average and variability of the measurement of flat sheets
- H1: The process is under control in respect of the average and variability of the measurement of flat sheets
- H0: The process is not under control in respect of the average and variability of the measurement of corrugated sheets
- H1: The process is under control in respect of the average and variability of the measurement of corrugated sheets
1.6 Scope of the Study
The scope of this study is limited to Emenite only in order to conclude the research work at the assigned period and the findings will be used to infer on the industry.
1.7 Limitations of the Study
During the course of this study, there were some problems encountered which stood as limitations to the research work. Some of the limitations include:
- Time Constraint:
The time frame given to accomplish this project was very short due to school academic calendar and it was carried out under pressure which made the researcher not to implement some necessary features.
- Financial Constraint:
Insufficient fund tends to impede the efficiency of the researcher in sourcing for the relevant materials, literature or information and in the process of data collection (internet, questionnaire and interview).
- Initial Cooperation Delay from Respondents:
A particular limitation of this work came as a result of the respondent refusal to offer their cooperation at the initial time they were contacted. This contributed in making the success of this research study difficult.
1.8 Definition of Key Terms
Variation:
This is a deviation from the normal standard or condition
Data:
These are sets of figures, raw information that is yet to be processed. e.g population data, employment data etc.
Control Charts:
It is the graphical display of the actual measurement of the characteristic on a chart showing limit which reflect the process capability on the particular quality characteristics.
Process Control:
This is the act of observing the functions of each of the factors leading to the production of goods on a continuous basis to ensure the process or means of production are kept in optimum conditions.
Product Control:
Product control is the act of measuring or observing different attributes of quality specification of a product with the aim of ensuring that the product conform to specification. This is done of taking a sample from a batch of inspection lot with the aim of accepting or rejecting it.
Statistical Quality Control:
This is the technique of sampling at every stage of production and statistical inferences are taken about the variability of the product quality.
Process Capability:
This is the minimum spread of specific measurement variation which will include about 99.73% of all measurements from the process.
